Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Wt vs Nt diffs
Wt vs Nt diffs
Hi after a bit of info and after looking through searches for the last hour no joy , must be there somewhere though .
Anyway In short how much wider is the wt compared to the nt and will a nt diff heaf straight swap into a wt .
See I have a couple of suzuki's here and thinking about swapping them all around a bit .
Cheers
Chris
Anyway In short how much wider is the wt compared to the nt and will a nt diff heaf straight swap into a wt .
See I have a couple of suzuki's here and thinking about swapping them all around a bit .
Cheers
Chris
I'm halfway through putting wt's in my nt with Damos help. Have been for a while come to think of it
The difference in width is only total 2 inches I believe Maybe 2" per side though not sure. But it's worth it for me cause the 1.3 gear is a bit stronger than the 1l.
You'll have to move the spring mounts inboard on the diff. The 1.3 nt centers will fit but not the 1l centers.
The difference in width is only total 2 inches I believe Maybe 2" per side though not sure. But it's worth it for me cause the 1.3 gear is a bit stronger than the 1l.
You'll have to move the spring mounts inboard on the diff. The 1.3 nt centers will fit but not the 1l centers.
Thinking of going spring over etc so want a pit more width and could then also move the spring perch in a bit . Must get under there and have a good look see then . Must be only 2 inch total as it doesn't look that much but I guess the flares cover it up a bit .
So then how do they compare to narrow toy axles ( 85ish ) , will get of my lazy but and measerue them tomorrow maybe but can't sleep so scheming you see .
Cheers
Problem is I have two sets 413 axles 1 set wt axles and one set toy axles and just trying to figure out which one will get which . ie run around car is a wt but does not need to be . Offroader has nt with difflocks , need more width . If I go toys I loose the lockers :-(
So then how do they compare to narrow toy axles ( 85ish ) , will get of my lazy but and measerue them tomorrow maybe but can't sleep so scheming you see .
Cheers
Problem is I have two sets 413 axles 1 set wt axles and one set toy axles and just trying to figure out which one will get which . ie run around car is a wt but does not need to be . Offroader has nt with difflocks , need more width . If I go toys I loose the lockers :-(
85zook wrote:this is gonna sounds strange but how bout putting the NT centres in the Toy pumpkins!! That way you increase the width AND keep the lockers.
The WT is about 9cm wider than the NT and as previously mentioned 1.3 NT centres will fit in the WT but not the 1L ones.
might want to reread what you just said. Zook diff centres don't fit into toy diffs.
cheers
[url=http://www.outerlimits4x4.com/viewtopic.php?p=930942#930942&highlight=]Zook[/url]
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
U SUK Zook Built and Sold.
New rig is 97 80 DX. 2" list 33s
Posts: 328
Joined: Sun Jun 27, 2004 10:35 pm
Joined: Sun Jun 27, 2004 10:35 pm
Location: Pimpin' zooks to disatisfied Jeep owners ;)
Contact:
nicbeer wrote:85zook wrote:this is gonna sounds strange but how bout putting the NT centres in the Toy pumpkins!! That way you increase the width AND keep the lockers.
The WT is about 9cm wider than the NT and as previously mentioned 1.3 NT centres will fit in the WT but not the 1L ones.
might want to reread what you just said. Zook diff centres don't fit into toy diffs.
cheers
You'd think that it could be done, considering the size of toy diff housings , a few mods may be, but then u run into the wall of axles to fit the housing width ( custom ones even- not cheap!) or cutting down the housing and rolling in new axel inner tubes?? To me, Vitara rear hosing is wider than a hilux housing and it fits w/t axels with minor mods and u can put in any zook diff centers you like with a lil re-ratio'ing. Use a widey housing upfront and ur keepin it all zook that way too!
People to do, Things to see ;)
Upgrade to L.E.D. on your rig! http://www.ledautolamps.com/
Upgrade to L.E.D. on your rig! http://www.ledautolamps.com/
raqmup wrote:You'd think that it could be done, considering the size of toy diff housings
It COULD be done but why bother. Weak link would then become the centres. Not to mention it would be cheaper just to sell his lockers and buy lockers for the toy diffs rather than stuffing around getting custom axles made etc etc
raqmup wrote: a few mods may be, but then u run into the wall of axles to fit the housing width ( custom ones even- not cheap!) or cutting down the housing and rolling in new axel inner tubes??
LOTS of rooting around. Would it be worth it? No.
raqmup wrote: To me, Vitara rear hosing is wider than a hilux housing and it fits w/t axels with minor mods and u can put in any zook diff centers you like with a lil re-ratio'ing.
Yes wider than hilux housing and WAY wider than a zook housing. Even a widetrack up front will still not match the vit rear. Hilux diff up front, yeah that might be coming closer but you cant match the ratios then. AND if you were using WT up front you could only match 4.56 or 5.13 ratios with the vit rear (unless you go aftermarket, cha-ching!)
If you wheel a lot and have been having breakages go the hilux diffs and do as -Mick- suggested (weld the rear and lock the front). Selling your zook lockers will get you some $ for a front locker.
If you dont wheel as much or haven't been breaking so much then go the WTs. SPOA if that's your thing (SEARCH for all the pro/con opinions on this) but dont go too high on the SPOA perch heigh as it will give your axe housing more leverage on the springs making for more spring wrap.
Another factor to consider is tyre height. If you are cool with running 31s forever then WTs will be fine. If you want to step up at some stage I would be putting in the hilux diffs sooner rather than later.
Posts: 328
Joined: Sun Jun 27, 2004 10:35 pm
Joined: Sun Jun 27, 2004 10:35 pm
Location: Pimpin' zooks to disatisfied Jeep owners ;)
Contact:
good points there Damo ! I was pretty much throwing a few ideas in the air and seeing which way they hit the ground... I guess having the vit/widetrack setup on mine is why I suggested it, we cut down the vit rear slightly on one side and put a section of housing tube onto the short side to make the driveline line up for the duel tfc set up (long story short, moved the pumkin across
The hilux set up is cool, I guess I'm just of the frame of mind to try and keep zooks zooks. The idea of running 33's with 5.13 centers permenantly is fine as it's been tried and tested for a number of years down here in VIC and has never blown a diff on the vehicles we've set up in the time that I've known them- not saying it's a given at all that they won't blow, just that they appear to be strong enough to take the load put on them by aggressive 33's.
Toydiffs are sometimes easier to come by and are a more than worthy swap, all depends on what weight an engineer will pass up there as well as what parts you've got at hand. Damo's right, if you've got the toyota parts there- use them and sell ur zook bits to counter-balance the change over
The hilux set up is cool, I guess I'm just of the frame of mind to try and keep zooks zooks. The idea of running 33's with 5.13 centers permenantly is fine as it's been tried and tested for a number of years down here in VIC and has never blown a diff on the vehicles we've set up in the time that I've known them- not saying it's a given at all that they won't blow, just that they appear to be strong enough to take the load put on them by aggressive 33's.
Toydiffs are sometimes easier to come by and are a more than worthy swap, all depends on what weight an engineer will pass up there as well as what parts you've got at hand. Damo's right, if you've got the toyota parts there- use them and sell ur zook bits to counter-balance the change over
People to do, Things to see ;)
Upgrade to L.E.D. on your rig! http://www.ledautolamps.com/
Upgrade to L.E.D. on your rig! http://www.ledautolamps.com/
Who is online
Users browsing this forum: No registered users and 1 guest