Notice: We request that you don't just set up a new account at this time if you are a previous user. If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
OK just get a little thread going see what people experience is with how much axle forward allows them to run the big meats.
i for one runn 35mm axle forward and love it
but on the next one i think 1" hanger forward with rears in front should net around 4" axle forward which i hope would keep up to 38's far enough out of the guards
i know richard runs 2" with only a slight bit of rubbing on 37's
http://www.budscustoms.com.au
Like us and follow on facebook for up to date information of what we are working on and great random specials!
I run rears up front which I think is about 2" forward
With 35's at the mo I have heaps of clearance but want to go 37's next
The problem I'm trying to get answers to is I know if you go too far forward there is problems with the draglink hitting the tie rod with hi steer. How far can you go forward before this is a prob. I think BJ mentioned a Daihatsu pitman arm to help with clearance.
suprasurf wrote:I run rears up front which I think is about 2" forward With 35's at the mo I have heaps of clearance but want to go 37's next
The problem I'm trying to get answers to is I know if you go too far forward there is problems with the draglink hitting the tie rod with hi steer. How far can you go forward before this is a prob. I think BJ mentioned a Daihatsu pitman arm to help with clearance.
I need to do more research 8)
Talk to the manufacturers of histeer eg Chaos 4x4 and they'll be able to answer your questions as they've done it all before. I'm currently fitting histeer to my vehicle with the front diff 4 1/2 inches forward so I'll see how it goes. The standard IFS pitman arm is the shortest toyota but not as short as the Diahatsu. Chaos make an adaptor to use the IFS pitman arm. I also had my stering arms made shorter than usual to bring the TRE closer to the diff. Also depend on style of TRE and thickness of steering linkages.
I measured my rear pack (that was installed in the front) and it measured 75mm difference from standard. Add the centre pin relocation on the perches and you get and extra 35mm so that's how I calculate 4 1/2 ". Others say it's less.
I have 40mm forward and 50mm wheel spacers and run Q78`s (just under 36) with NO rubbing at all, but fark it is close, like about 2mm when tyres were new.
Fixing the binding issue with the D/L and T/R is easy just move the steering box as far forward as possible even if it means cutting into the rad support and the cab mount. Shortening the arms only makes the steering box and all components work harder.
RUFF wrote:Fixing the binding issue with the D/L and T/R is easy just move the steering box as far forward as possible even if it means cutting into the rad support and the cab mount. Shortening the arms only makes the steering box and all components work harder.
Tony talks out his a$$!!!!
actually no seriously tony has done his and it works well, he did it how he decribes and it steers well. the 38s rubbed, but it did not have much lift, and his tyres measure 40" x 16"
RUFF wrote:Fixing the binding issue with the D/L and T/R is easy just move the steering box as far forward as possible even if it means cutting into the rad support and the cab mount. Shortening the arms only makes the steering box and all components work harder.
That's what I thought with the extra stress due to the shorter arms but chaos did them this way to account for the diff relocation although I hadn't asked them to do it. Once they had, then I figured that I'd give it a try. Eventually I want to go hydro assist so the stress wont be too big of an issue.
My steering box is already rubbing the paint off the rad support panel so I shouldn't have too many issues.
RUFF wrote:Fixing the binding issue with the D/L and T/R is easy just move the steering box as far forward as possible even if it means cutting into the rad support and the cab mount. Shortening the arms only makes the steering box and all components work harder.
That's what I thought with the extra stress due to the shorter arms but chaos did them this way to account for the diff relocation although I hadn't asked them to do it. Once they had, then I figured that I'd give it a try. Eventually I want to go hydro assist so the stress wont be too big of an issue.
My steering box is already rubbing the paint off the rad support panel so I shouldn't have too many issues.
my box aint rubbing paint off the support as i put a holesaw thru mine and moved it even further forward
