Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

salisbury problem

Tech Talk for Rover owners.

Moderator: Micka

Post Reply
Posts: 827
Joined: Thu Apr 28, 2005 7:52 pm

salisbury problem

Post by F'n_Rover »

Is it possable to further crush the pinion preload sleeve by hitting and draging the pinion flange across ruts/rocks ?

All hell broke loose with the rear sals. Its 100% ok when cruising under throttle but when backed off or in neutral it sounds like someone is going stupid with a sledge hammer and a bag of marbles in a tin can. All was going ok until the last track of the weekend when i got bogged and hung up in some stupid arse ruts. Also the pinion seal is leaking BIG TIME :oops: and there is heaps of slop in the pinion / tailshaft - you can wiggle it lots. (it could just be a collapsed bearing)???

This diff is comming out anyway as the rebuilt maxi is almost ready, But if there is a known problem with the crushable sleeves - i'll re-do this area with a solid slug on the new diff.

Any ideas??

thanks
Simon
Last edited by F'n_Rover on Sun Jan 29, 2006 10:35 pm, edited 1 time in total.
Ex-Army - SeriesIII -186s - NP435 - Maxi rear - megasquirt coilpack ignition - AM FM radio with 2 X speakers
Posts: 16934
Joined: Sun Oct 20, 2002 6:57 pm

Post by RUFF »

If the Pinion was loaded and the inner pinion bearing was pushed hard home at the time the flange was hit it is possible for the flange to move inward. Then the crush sleave can be compressed more. If this is the case the flange can be removed and you can add some shims to the end of the sleave so you can then get the right pre-load again. Or its pull the centre and pinion and replace the sleave. Unless the sleave can be removed with the flange removed and the outer pinion bearing removed. But im not sure if this is possible with the Salisbury. Its not with a Toyota Diff.

It is a much better set up to run solid spacers.
Posts: 783
Joined: Sat Jan 01, 2005 1:34 pm
Location: Narellan NSW

Post by andrew e »

does anyone know the seal size for the rear salisbury pinion? its cheaper if i order it through work as an everyday seal rather than through landrover as a pinoin seal.
Posts: 827
Joined: Thu Apr 28, 2005 7:52 pm

Post by F'n_Rover »

I dropped the tail shaft today and found the pinion nut had backed off. Re-tightend it bush mechanic style :? (in between tight and stupid tight) All good now. Got me stuffed how it undid itself.

Andrew - ive got a new land rover pinion seal at work, I'll have a look for an OEM part number on it. Although dont hold your breath.
Ex-Army - SeriesIII -186s - NP435 - Maxi rear - megasquirt coilpack ignition - AM FM radio with 2 X speakers
Posts: 5803
Joined: Wed Feb 19, 2003 3:02 pm
Location: Brisbane

Post by ISUZUROVER »

RUFF wrote:Unless the sleave can be removed with the flange removed and the outer pinion bearing removed. But im not sure if this is possible with the Salisbury.

It is a much better set up to run solid spacers.
Yes it can be - at least I did it that way on my 110 when I replaced the pinion seal. Sorry Andrew I have no idea what size it is.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
Posts: 463
Joined: Sun Nov 21, 2004 10:15 pm
Location: Kingston,Hobart, Tasmania

Post by justinC »

OE part number for seal is AEU 2515

Jaguar XJ 6 pinion seal will fit, and is of better quality, ie rubber not leather, not very expensive either.
JC
'92 Rangie Sherwood/turbo intercooled isuzu4BD1 /ACE/ full leather/2.5" exh/2.5" body lift/DeCarbon shocks/LR tanks/LT95 back in and OK now, Sals conversion soon...
Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest