Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Bolting coils in

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 9393
Joined: Tue Oct 29, 2002 11:51 am
Location: Brisbane

Bolting coils in

Post by antt »

just wondering how you guys with heaps of articulation have bolted your coil springs in so they don't drop out at max flex?
pics would be good to :D
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

yes. :)
Top
Posts: 329
Joined: Thu Nov 07, 2002 5:24 pm
Location: Brisbane

Post by derangedrover »

Carlton prefers to use small green nylon rope as a coil retainer, this way he can completely remove his shocks and get much better flex :crazyeyes:
Top
Posts: 4065
Joined: Thu Oct 24, 2002 8:31 am
Location: ACT

Contact:
Contact Wendle

Post by Wendle »

derangedrover wrote:Carlton prefers to use small green nylon rope as a coil retainer, this way he can completely remove his shocks and get much better flex :crazyeyes:


Ahhh, nostalgia! She was a bumpy trip home that day....

I still haven't made up the little tabs for the bottom of the front coils, been talking about it for a fair while now! :D

Do you have the photo of my ropemanship handy??
Top
Posts: 571
Joined: Tue Nov 19, 2002 3:56 pm
Location: New York

Post by zzzz »

me too :)
no pics
Top
Posts: 1175
Joined: Mon Dec 09, 2002 6:25 pm
Location: sydney

Contact:
Contact XXXL80

Post by XXXL80 »

surfection (jeremy) had a good little system in place that i saw on the surf, he welded tabs top and bottomto hold the coil in. i think the tabs were welded to the chassis and the diff and then bent over in a right angle over the top of the spring. should PM him and see if he could take a digi of it.
Top
User avatar
POS
Posts: 4318
Joined: Tue Oct 22, 2002 8:52 pm
Location: Perth

Post by POS »

Just get some 25x25 angle iron and cut in a 20mm wide strip and weld it on hooked over the spring!
Top
Posts: 329
Joined: Thu Nov 07, 2002 5:24 pm
Location: Brisbane

Post by derangedrover »

Wendle wrote:
derangedrover wrote:Carlton prefers to use small green nylon rope as a coil retainer, this way he can completely remove his shocks and get much better flex :crazyeyes:


Ahhh, nostalgia! She was a bumpy trip home that day....

I still haven't made up the little tabs for the bottom of the front coils, been talking about it for a fair while now! :D

Do you have the photo of my ropemanship handy??


Was all set with the photos
took the few films in i had to get developed....
and then realised when I got the photos back that I had loaded the same film into the camera twice :bad-words:
Top
Posts: 2388
Joined: Sun Nov 24, 2002 10:20 pm
Location: bacabugari

Contact:
Contact big red

Post by big red »

i welded extra bracing from the lower spring mount to the diff housing in the front and rear of the spring mount [ braces sit in the vertical plane ]
These braces have a nut welded behind them .
I then bent a bit of 25 x 3 flat into a "U" shape which sits upside down over the bottom coil run and bolt into the braces.
I then welded cones to the top spring mount to guide the spring back into place if it goes down to far. worked for 2 years so far.
shane :D
[url=http://bigred.redbubble.com/][color=red][b]You can follow me but its gunna hurt ![/b][/color][/url]
event pics http://bigred.redbubble.com/
Top
Posts: 207
Joined: Wed Dec 04, 2002 8:45 am
Location: Over there

Contact:
Contact Bodge

Post by Bodge »

Hose clamp.


...if it breaks use more next time...
The Lucas motto: "Get home before dark."
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 0 guests