Hi chaps.
Looking at the front of the chassis, and there are 2 holes with nuts inside the chassis, but the center to center of the holes is only 35mm.
This dosent match with the recovery hooks ive looked at.
What did you do to fit recovery points on your lux's.
I have some ideas, however I am always willing to learn from others mistakes/ experiences/ successes too.
Trains
Ps, any suggestions for a good 4x4 shop in Adelaide to get this stuff from?
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Fitting recovery points on a 95 hilux Ln106
Moderators: toaddog, Elmo, DUDELUX
Fitting recovery points on a 95 hilux Ln106
Save the Whales......Collect the whole set.
My Wife Can't Shear..............But You Should See Her Crutch !
My Wife Can't Shear..............But You Should See Her Crutch !
All Bushranger etc hooks are 35mm centres as are old #J40 series hooks .
The front chassis on a Hilux needs reinforcement to prevent the captive nuts distorting or pulling through the chassis. A 5mm plate either welded to the chassis under the mounting holes, or if that raises legal issues, a 50 x 5mm plate with 3 holes in it the 3rd hole being the factory bolt hole behind the 35mm spaced pair. These 3 holes are not in line so measure twice cut once.
J Top
The front chassis on a Hilux needs reinforcement to prevent the captive nuts distorting or pulling through the chassis. A 5mm plate either welded to the chassis under the mounting holes, or if that raises legal issues, a 50 x 5mm plate with 3 holes in it the 3rd hole being the factory bolt hole behind the 35mm spaced pair. These 3 holes are not in line so measure twice cut once.
J Top
Thankyou J Top,
Just the information I required.
Will make up a plate as you suggested, and get some from a Bushranger supplier.
Many thanks again.
One more question, the thread type for toyotas captive nuts, is that the same as the bolts that will come with the hooks?
Or do I get them (High tensile ones) from universal fastners, if so what is the thread size/ pitch I will ask for?
Cheers
Trains
Just the information I required.
Will make up a plate as you suggested, and get some from a Bushranger supplier.
Many thanks again.
One more question, the thread type for toyotas captive nuts, is that the same as the bolts that will come with the hooks?
Or do I get them (High tensile ones) from universal fastners, if so what is the thread size/ pitch I will ask for?
Cheers
Trains
Save the Whales......Collect the whole set.
My Wife Can't Shear..............But You Should See Her Crutch !
My Wife Can't Shear..............But You Should See Her Crutch !
If you have a ARB bullbar fitted as I do then you can put recovery hook to this. There are 2 holes pre drilled in the bar just in front of where the hook would mount to your chassis. There are two holes either side of bullbar. I rang ARB as I was concerned of the old theory dont recover from a bull bar but ARB told me that these holes are pre drilled in these spots for that exact reason. Have recovered many times from these points and no damage or distorsion to bar or chassis.
Just an update.
I made up some brackets out of 3mm steel, and drilled the off set holes, and it all fitted up wonderfully, untill I went to tighten the spring shackle nut, and could only get the open ender on the nut.
I could not get enough purchase on the nut to sufficiently tighten it.
Bugger !
Trains
I made up some brackets out of 3mm steel, and drilled the off set holes, and it all fitted up wonderfully, untill I went to tighten the spring shackle nut, and could only get the open ender on the nut.
I could not get enough purchase on the nut to sufficiently tighten it.
Bugger !
Trains
Save the Whales......Collect the whole set.
My Wife Can't Shear..............But You Should See Her Crutch !
My Wife Can't Shear..............But You Should See Her Crutch !
Who is online
Users browsing this forum: No registered users and 75 guests