Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

how to change a uni joint?

General Tech Talk

Moderators: toaddog, TWISTY, V8Patrol, Moderators

Forum rules
Post Reply
Posts: 614
Joined: Tue Jul 27, 2004 7:47 pm
Location: Penrith

Contact:
Contact UZJ40

how to change a uni joint?

Post by UZJ40 »

never had to change one before, i got the cir clips off, but thats as far as i got!

how do i get the bearing caps out? the w/shop manual shows a special service tool but there has to be an easy way.

its a cruiser
HoldFast RocKrawlin
Top
Posts: 338
Joined: Tue Dec 27, 2005 7:20 pm
Location: QLD Ipswich

Post by 4x4Monkey »

get a socke that fits the exact size of the cap and belt the living shit of of the socket to either the cap breaks apart of it pushed all the way in and pop the cap on the other side out
then do the same fo the other side
Dont worrys There's No Sugar

My 4x4 Is too clean.... Needs a Mud Pack
Top
Posts: 1151
Joined: Sat Jul 23, 2005 1:48 pm
Location: Does lost count?

Post by midnight »

A vice is handy. But yes, as was stated, get a socket that sits just inside the lip, and a decent hammer, and start beating the living snot out of it. It will either shatter, or start pushing out the other side.
Top
Posts: 50
Joined: Sat Jul 16, 2005 5:11 pm
Location: Ballarat

Contact:
Contact stoo2

Post by stoo2 »

i tried all that, then cut the shit of a thing out with an angle grinder.
the disc didn't touch anything that wasn't replaced.
:)
Top
Posts: 156
Joined: Tue Sep 27, 2005 7:23 pm
Location: Dandenong ranges

Post by Dyna Beast »

The best bit is installing the new unijoint.Fit one cap in with center piece in place.In a perfect world gently tap oppisite cap on .Reality and the real world, a fair chance that one of the needle rollers will dislodge wilst the cap is being tapped on,This will only be dettected when the cap will not go all the way in to allow the cir clip on.Now all you need to do is remove the cap that has been almost all the way on with out stuffing it.This may accur several times with more than one cap.This can be the beginning of that love- hate relationship that people speak of when owning a 4wd. :D
Cheers
Hybrid rover ute. Isuzu diesel. Custom suspension. Winch. Snorkel etc. etc.
Top
Posts: 736
Joined: Mon Mar 07, 2005 5:25 pm
Location: Redcliffe, Brisbane

Post by chops »

http://www.turbophile.com/technical/uni_joints.html
1988 351W GQ wagon
Top
Posts: 3523
Joined: Fri Aug 27, 2004 12:27 am
Location: Fairfield,Sydney

Post by pongo »

stoo2 wrote:i tried all that, then cut the shit of a thing out with an angle grinder.
the disc didn't touch anything that wasn't replaced.
:)
Yep, easiest by far i reckon
Top
Posts: 3099
Joined: Wed Dec 11, 2002 10:55 am
Location: Central Queensland

Post by BundyRumandCoke »

A better way than Dynas advice above, is to use the same socket and a vice to reinstall. Use the socket to push the cap into the tailshaft. This generally doesnt dislodge the needle bearings. It also helps to grease the outside of the end caps where they go into the shaft.
Mud makes excellent toothpaste.
Top
Posts: 614
Joined: Tue Jul 27, 2004 7:47 pm
Location: Penrith

Contact:
Contact UZJ40

Post by UZJ40 »

thanks guys, thought that might be the answer. ;)
HoldFast RocKrawlin
Top
Post Reply

Return to “General Tech”

Who is online

Users browsing this forum: No registered users and 3 guests