G'day all,
I am rebuilding the front diff in my Stage I at the moment (at long bloody last). I have decided to do a conversion to Bearings in the swivel housing (normally has a bush in the top)
Also is it worth keeping the Stage I CV's to use in my project 90 ? The Stage I CV's are stronger than the RR ones aren't they? and i would fit RR ones to the Stage I. Would it be worth it?? or just keep the RR's in my project and Stage I CV's in the Stage I ??
Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
Stage I CV's
Moderator: Micka
Stage I CV's
[i]DAS[/i]
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
Well there ya go i was under the impression that sieries 123 were fitted with uni joints on the front simaler to sheep and boards with danas.
While your there das on the rear diff of a series3 salsbury does the wheel bearing flange unbolt from the housing via five or six bolts ?
Like the front does for the swivel hub on a rangie
Larry.
While your there das on the rear diff of a series3 salsbury does the wheel bearing flange unbolt from the housing via five or six bolts ?
Like the front does for the swivel hub on a rangie
Larry.
Dozoor wrote:While your there das on the rear diff of a series3 salsbury does the wheel bearing flange unbolt from the housing via five or six bolts ?
Like the front does for the swivel hub on a rangie
Larry.
If you mean the stub axle?? then yes they are held on by 6 bolts I think (I can check if you want)
suzidisco wrote:Keep the stage 1 cv most people go to the hassle of putting them in after breaking the smaller disco/rangi cv.
Do you mean keep the Stage I CV's in the Stage I ? Or keep the Stage I CV's for my project 90? (which is running a RR front diff)
Tony78rr wrote:Have you ever priced stage 1 half shafts OOUUCCHH!!!!!!!!!.
Yes I have....I just bought 2 new ones as I twisted both the front ones (and one broke). It was cheaper to buy maxi-drive ones than standard ones.
[i]DAS[/i]
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
MY05 4.4L V8 Range Rover Vogue
Series 2a Buggy....In the Building
The only problem you have is DAS....
the stage 1 drive flanges/hubs are 6-bolt and the RR are 5-bolt. So you would need to get some defender drive flanges to fit the stage 1 CV's to the 90 (or buy MD ones at about $120 each), and you would then need to get county or 200Tdi defender rear hubs (drum type) to be able to bolt the RR drive flange/stub axle assembly to the new front hubs. Other than that it should all swap over.
the stage 1 drive flanges/hubs are 6-bolt and the RR are 5-bolt. So you would need to get some defender drive flanges to fit the stage 1 CV's to the 90 (or buy MD ones at about $120 each), and you would then need to get county or 200Tdi defender rear hubs (drum type) to be able to bolt the RR drive flange/stub axle assembly to the new front hubs. Other than that it should all swap over.
_____________________________________________________________
RUFF wrote:Beally STFU Your becoming a real PITA.
Who is online
Users browsing this forum: No registered users and 0 guests