Outer Limits 4x4 Board

Hey all i have a 12v mk with a chev and i'm removing that and putting a sd33t in and need some pointers on how to wire it in. I need to know how to wire up the D.P.C module. The fuel pump side is easy just the other side. I'v read some stuff bout going to ignition barrel to change pump at different ...

hey guys i'm looking at making a set of sliders for my patrol and want to buy some mandrel bends instead of actually bending them i'm looking at bout 60mm tube or there abouts haven't got any tube yet so size not really important. Just want to know where on the northside of brissy to buy them from ...

hey mate, I bought a dellows kit for my 350 into mq and it was great completely hassel free. With very simple instructions if you can weld you can do the conversion. As for the gearbox i've got a 350 crate motor making 290hp and 35's done 4000k's so far no probs, taken it off road get up it on the ...

hey guys, Thanks for the replies. Currently the plugs i have in it are 6's what should i put in it??? I have a holley street dominator manifold with holley 600vac sec carby! When i refitted the head bought a full gasket set in the felpro brand. The PCV valve is plumbed into a spacer underneath the ...

Hey guys thanks for the replies. I have fitted new rings to that cylinder which rules out a broken ring. When i refitted the head i put gasket sealer aswell as a new gasket. How do i check for blowby?? I fitted new valve stem seals to no. 8 last friday and have done bout 90k's since and it has ...

Hey all, I have fitted a crate 350 into my mk and have done bout 3000k's since and now the no. 8 plug keeps fouling up. Every 100k's i have to pull it out and clean it up. When the plug is pulled out it looks like it has come out of an older car and is caked up with burnt oil. And if it idles for ...

hey all,
I have a h233 lsd in my mk swb and i blew the pinion mate gears up in it. And marked the side gears when they went. I have been offered a h260 lsd centre. Will the gears fit in my centre or are they different centres all together?

Cheers Rees

Hey you also need to pay your third party insurance to drive the car to get RWC and to QLD Transport.

Cheers Rees

hey mate,

I got my arb winch bar lifted for 2 inch body lift at superior for $275!!!

Great job would highly recomend taking it to someone who is a competent welder and an idea of how to brace it up.

Cheers Rees

hey jesse. http://cgi.ebay.com.au/LPG-GAS-System-IMPCO-Gas-carby-Tank-convertor-suit-V8_W0QQitemZ290080152515QQihZ019QQcategoryZ36612QQrdZ1QQcmdZViewItem I found this on ebay is this what i'm after or is it no good??? I seen you had your mq for sale with gas kit and no motor!!! Wouldn't be ...

Hey V8PATROL,

You wouldn't have any photos of under your truck with the tanks?
Just to give me an idea on what to do if thats the path i take!!

Cheers Rees

hey thanks for that jesse!!! Is there just a kit i can get installed or is what you are describing a non-standard setup. And can i do any of it myself or does someone have to do it that is trained to? I've got a 650 square bore on at the moment. whats the idea behind the big holley?? I think i heard ...

Thanks for the reply. Am i able to get a custom tank made legally?? Are Scuba tanks legal?? And does anyone know the length and diameter of a standard gas tank??? I'm going to be going to moreton island a bit and there is no gas over there hence the reason for large capacity!!! Any one got better ...

Hey I've got a swb mk with 350chev. I want to run it on a gas research system(straight gas). My question is i want a custom tank made that will fit in the original spot. And have larger capacity eg. 120-130ltr+. And not loose ground clearance. Which is why i don't want a standard round one. Can a ...

Mate not sure bout the au fans but el ones pretty much go straight on just a tiny bit of trimming and make some brakets to hold them on!! I just used some hoopine strap and a couple of tek screws!! I'll get some pics for you tomorrow. Really it only took me 30 mins to fit.

Cheers Rees

mate a standard mk radiator is pleanty good enough for a 350 chev as long as u put el falcon twin thermos on. Thats what i have on my mk with a chev and it runs at 75degres all the time even on the beach. Make sure your radiator gets flushed before fitting the v8.

Cheers Rees

hey mate do you mind me asking how much your picking it up for??
My old man has one that he is thinking of getting rid off but has no idea what their worth??

Cheers Rees

mate go to the wreckers buy a set of gq belts and swap just the strap over to yours. Make sure you clamp the drum when its un wound other wise it will be usless when it unwinds. and dont let the belt roll right up or you wont be able to undo it.

Cheers Rees

mate i got mine done at rob bliss as well and it is brilliant and they don't charge too bad. I would recommend them to anyone!!!

Cheers Rees

hey guys i got a new hood lining made for my mk swb. I got it made from vinyl i ahve the windscreen out and i'm TRYING to fit this hood lining but with no luck i can get it in but it gets wrinkles in the corners :x . i have tried heating it up with a hair dryer but it doesn't work for me. maybe i ...

i've put a 350 chev into my mk swb got the kit off dellows was excellent straight forward. and only cost $1000 delivered to my front door. and i got every thing except pressure plate!!!!!! I highly recommend them and would use them again if i done another!!!!!

Cheers Rees

hey broken80 where did you get that box made cause i WANT one and will it fit on to a holley or only a quadrajet???

Cheers Rees

give him a break!!!! OBVIOSLY He's on his P plates and probably his first 4WD may, not be as flash as yours but he's having a go!!! All things take time he might even end up with a better 4WD than YOU!!!!!

Rees

i have marked it where i want it to end up and do i just cut it off then weld a plate inside or do i get some bent up to fit inside then weld????? Whats the go whats everyone else do???? pics???

Can someone please inform me of a method of cutting quarters of my mk swb. once marked then what????? where to start please help??? and i looked at the bible but no info just some pics.

Cheers Rees

mate don't trust the sales person on your bearings or rings it can be an expensive mistake. get some plastigauge to check bearing clearance and use your feela gauges to check ring gap. If you want to know anything more PM me.

Cheers Rees

i'm in the north side of brissy. that would be great if i could lend a hand to get a good roll bar. even if you could send me a set of plans when done if your not near me and i could get one made.

Cheers Rees

4130warrior thats EXACTLY what i want is to be able to have 4 people in the car no matter what. i was thinking alloy in bout 90-100mm pipe i've been looking for somewhere to get it done but no-one knows what i want or don't do that sort of stuff. :cry: but anyways just keep looking i suppose. Cheers ...

Cheers. Thanks for the replies i think i'll try find one now. Any one got one?

Cheers

Rees

Cheers. Thanks for the replies i think i'll try find one now. Any one got one?

Cheers

Rees