Outer Limits 4x4 Board

I know, I know. but it is a 2010 and worth some $$$$. seating change means engineers cert doesn't it? i am thinking of going the other way for my 105.

Depends what it is going into you would also need to use the 7X's transfer box as the input/output shafts are different. If it were a conversion i would use the engine, gearbox and transfer out of the 7X series

Yes it can and has been done.

http://sleeoffroad.com/project_vehicles ... s_paul.htm
http://sleeoffroad.com/past_projects/pr ... hicles.htm

I have those Safe-n-sound ones in my cruiser, head allways seams to stay back.

Can the Pajero rear (iRs) and corperate 14 bolt be flipped for the front ( iFs)?

Tectyl 506 and NEW oil mix

This company make them for ON road use http://www.mcdonaldbrosracing.com.au/suspension1.html

If the front wheel bearings have just been done maybe the hubs are not correct even though they look ok.

Have you tried the pub? best place to start looking for anything.

Might be ok
http://www.advanceadapters.com/products/pn-717006/

I got no cup holder or ABS, but i do have 2 holder that fit a stubby and cooler in the fold down middle seat and 3500kg towing

Have you tried spinning the tyre on the rim? it takes awhile but you can balance the tyre to the rim and use less weight.

First hit in google http://www.sealtite.com.au/products/cat/51

+60. Also check the load rating (1250 for 200 and 950 for the 100)

starky wrote:no not the same as 100 series i have been told

You have been told wrong info, the stud pattern is the same, but depending wich way you want to go the wheels might not fit (100-> 200 no as the brakes are bigger unless you have 17" 100 series rims)

I rebuilt my pump on my 1FZ-FE Landcruiser pump for $110. Bearing, seal, o-rings and new shaft. This pump is a gear driven pump but they are nearly all the same inside.

This

pump on a 1HZ. Wasn't hard to do and learnt a bit on the way.

Yep same as above for mine (pump only not box)

$110 ...

I just typed in "how to replace a uni joint" and about 5 came up on youtube and about 100 sites
http://flashoffroad.com/Maintenance/Ujoints/Ujoint.htm

What is that black or grey stuff they use to hold the plastic behind the door cards on?? that might work!!

Just found this site!!

http://gasolineimports.com/?page_id=13

* Parts - pallet shipment $350
* Parts - small parcels from $30
* Parts - engines $160 *Parts - transmission $120

This place have some good prices.
http://www.tyreshop.com.au/shop/index.p ... path=35_45

Didn't the bloke/company that fitted your Steinbauer chip offer/give any info on the exaust?

1st result in the search
http://www.outerlimits4x4.com/viewtopic ... &hilit=1jz

Worst case if the cable breaks its going to slam back down on the trailer frame, possibly damaging it, but i doubt anyone would be injured.

This is the thing that I think would be a bit unacceptable without a safety feature. But thinking about it, I don't think it would be too hard to come up ...

shakes wrote:I've had good dealings on a few occaisions with this guy...

http://www.traxide.com.au/Traxide.html" onclick="window.open(this.href);return false;

X2

esp22 wrote:Hi, where do i get an intercooler from for the 12ht..havent seen much apart from ase?

Thanks

Send a pm to turboshop he is a member on this forum.

x2, as above

I just use the foam buff pad and autosul (sp)

I put a Turbo glide kit on mine, all good so far. confused yet

http://www.outerlimits4x4.com/viewtopic ... 3&t=217822

When i got the turbo for mine, it came with a 2.5" system, i asked about the 3" and was told that the 2.5" was all that is needed.