Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

3.5l carb option

Tech Talk for Rover owners.

Moderator: Micka

Post Reply
Posts: 16
Joined: Mon Feb 18, 2008 5:23 pm
Location: Napier

3.5l carb option

Post by moonhopper »

I Have a set of standard stomberg carbs on an 86 3.5l rangie, i'm sick to death of the carbs giving me hassles, was told that the holly carb is a better option, if this is the case, what should i be looking for, 2 barrel , 4 barrel etc. and about what should i be paying for them.
Posts: 1606
Joined: Sat Oct 26, 2002 7:20 pm
Location: Geelong

Post by HSV Rangie »

nope no holleys you will have flooding issues on slopes.

Michael.
Mitsubishi 2010 NT DID Pajero wagon, Factory rear diff lock, Dual batteries, ARB bar, winch, Mt ATZ 4 rib tyres.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
Posts: 16
Joined: Mon Feb 18, 2008 5:23 pm
Location: Napier

Post by moonhopper »

if not holley, what is my best option as i've had a guts full of constant problems with these carbs
Posts: 22
Joined: Sun Jun 18, 2006 12:07 am
Location: Seaford, Victoria

Post by waxen »

Holley's are OK with a couple of minor mods, namely a 350 with a vent tube extension and mounted back to front works fine.
Posts: 16
Joined: Mon Feb 18, 2008 5:23 pm
Location: Napier

Post by moonhopper »

whats involved in going EFI
Posts: 32
Joined: Mon Aug 20, 2007 9:20 pm
Location: mornington peninsula

Post by firey69 »

running petrol or lpg or dual fuel?
Posts: 16
Joined: Mon Feb 18, 2008 5:23 pm
Location: Napier

Post by moonhopper »

just running petrol 96 octane, i can get aEFI of a 3.9 disco, just would like to know whats i'm getting into before i give it a go
Posts: 66
Joined: Tue Jan 22, 2008 3:30 pm
Location: Central Coast NSW

Post by armbrup »

If you cannot get Strombergs to run correctly, then I doubt that you will be able to install injection.
Strombergs are about the simplest trouble free thing there is. There are let me see about 3 or 4 moving parts.
I suggest that you perhaps have them overhauled by someone who knows them and they will go for years without adjustment.

It will cost quite a lot to install injection. I have done it with Federal Injection on a 77 but the gains were virtually nil on a stock 3.5. and it is a LOT of work.
You have to either use an injection tank or make up a swirl tank,all the fuel lines need to be replaced with high pressure lines which is very expensive, you need to organise and buy a pump, filter etc and work out somewhere to put them.
The actual placing of the injection on the engine is plug and play, except you should grind a notch in the top of the ports for injector spray clearance.
If you get injection, try to get the manifold, loom, ECU, fuel lines , tank(with pump) etc. If it is only a manifold or bits are missing give it a miss.
Its the bits and pieces that will nickle and dime you to death.
Regards Philip A
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests