Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.
rear diff
Moderator: Micka
rear diff
well i have broke 2 rear diffs in 1 week. same thing both times. centre pin snapped. have got the whole replacing it thing down to an art. can do it in less that 2 hours. but..i dont want to be doing this. i have done a huge search on toyota centres conversion..not that i know wat all those numbers and ratios mean. can someone tell me exactly wat i need in laymans terms? ie you need a diff from a 1980 hilux. blah blah..
or
is it worth me maybe just to buy a locker for the rear and upgrade my axles?
thanks ..im not trying to be a pain!!!!
or
is it worth me maybe just to buy a locker for the rear and upgrade my axles?
thanks ..im not trying to be a pain!!!!
Toy diffs.
rear low pinion.
pic a ratio that returns gearing to Std with the tyre diam you wish to run. (Have a excel spread sheet that I can email you)
Front: Hi pinion or jacmac centre. (need to be hi pinion to clear steering.)
If required I have a template/jig that can be used for drilling the Rover housing.
new studs M8 buy 30mm 8.8 studs.
8mm tap and drill tosuit.
Axles:
Rear: Jac mac inc flanges around $700.00
will require rear spindle to be bored out about 20 thou. aprox $40.00 for both.
Front: Jac mac axles around $550-600.00
will have to decide which CV you wish to run.
If you run toy cv you will need drive flanges.
Spindles again have to be bored if you go with 30 spline toy cv.
Swivell ball housing needs to be bored 20 thou aprox.
pinion flanges (toy diff) need to be machined and drilled to take rover drive shaft.
Michael.
rear low pinion.
pic a ratio that returns gearing to Std with the tyre diam you wish to run. (Have a excel spread sheet that I can email you)
Front: Hi pinion or jacmac centre. (need to be hi pinion to clear steering.)
If required I have a template/jig that can be used for drilling the Rover housing.
new studs M8 buy 30mm 8.8 studs.
8mm tap and drill tosuit.
Axles:
Rear: Jac mac inc flanges around $700.00
will require rear spindle to be bored out about 20 thou. aprox $40.00 for both.
Front: Jac mac axles around $550-600.00
will have to decide which CV you wish to run.
If you run toy cv you will need drive flanges.
Spindles again have to be bored if you go with 30 spline toy cv.
Swivell ball housing needs to be bored 20 thou aprox.
pinion flanges (toy diff) need to be machined and drilled to take rover drive shaft.
Michael.
Mitsubishi 2010 NT DID Pajero wagon, Factory rear diff lock, Dual batteries, ARB bar, winch, Mt ATZ 4 rib tyres.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
1986 RR.
Custom suspension links etc.
HSV 215 engine.
4.3 diffs.
walker wrote:You would be looking at about $1300 for an ARB locker + approx $850 for the maxi-drive axel kit. I think a maxi-drive locker would be a bit more.
Whatever you do you have to do the axels so in that case an ARB locker would probably be cheapest.
plus about another $300 for the compressor etc..
just get the whole maxi drive and be done with it
just over $2k fitted
i got mine fitted aby dave at Hardcore 4x4 in mitcham and havent looked back since
Gu TD42t
[url]http://www.3rdrock4x4.com[/url]
[url]http://www.3rdrock4x4.com[/url]
fightara wrote:Or for cheapness sake you could just upgrade the rear to 24-spline discos and whack in an airlocker to get teh 4 hemispheres
That's what I have done. Bits for the 24spline conversion cost $250, but that was for the whole axle housing disc to disc. Plus I sold (well swapped for Bundy ) my old 10 spline hubs and stubs. The ARB cost $1050 and the loom $30. Already had all the other bits.
Only have 31's at the moment until I get my body lift and a few other things sorted.
Luke
'88 Rangie, 3.9i, Bilstein Shocks and RS Springs, ARB Lockers F&R, 24spline rear axles, Flares, [url=http://users.on.net/~vethaak/Projects.htm]Custom centre console and cargo shelves[/url]
Who is online
Users browsing this forum: No registered users and 3 guests