Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

Patrol axle seal

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Forum rules
Post Reply
Posts: 5457
Joined: Sun Oct 27, 2002 9:49 am
Location: Sydney

Patrol axle seal

Post by Shorty40 »

Rear axle seal on a 92 GQ Patrol.

Is it a difficult job for a guy with minimal mechanical skills ?

Any tips ?
Top
Posts: 45681
Joined: Wed Nov 27, 2002 10:13 am

Re: Patrol axle seal

Post by bogged »

Shorty40 wrote:Rear axle seal on a 92 GQ Patrol.

Is it a difficult job for a guy with minimal mechanical skills ?

Any tips ?
you need a VERY heavy press since while there you may as well do the bearings
Top
Posts: 676
Joined: Sat Jul 23, 2005 6:03 pm
Location: Maroochydore

Post by cutzook »

fark the seal and get the buggy on the trailer man. lets go tomorrow arvo.
Top
Posts: 1170
Joined: Tue Jun 01, 2004 4:27 pm
Location: Goodna, Queensland

Post by Bartso »

the actual seal in the housing easy just use rubber hammer all good
MUD BEERS & MAYHEM 4x4 & SOCIAL Group
[url=http://www.fourbys.com.au/]Fourby's tyre and mechanical[/url]
[url=http://www.4wdmonthly.com.au/forum/showthread.php?t=24441/]My build up for ttc[/url]
Top
Posts: 2820
Joined: Sun May 25, 2003 10:04 am
Location: Redbank Plains, QLD

Post by Daisy »

88 bux for a patrol rear axle from wreckers... saves time and heartache me thinks...
custom bar work, 4x4 parts, trailers, anything out of steel/alloy :D
Top
Posts: 5457
Joined: Sun Oct 27, 2002 9:49 am
Location: Sydney

Post by Shorty40 »

Well, the seal is out :D I will take it to Ripco tomorrow and get a new one (and a new O-ring aswell) and pop it all back together.

Wasn't as big a job as I was expecting :cool: Wheel off, brake caliper off, disk off, undo 8 nuts, slide out axle then pop the seal out :D

Bruce - the bearings were replaced not too long ago, so they are ok
Top
Posts: 1170
Joined: Tue Jun 01, 2004 4:27 pm
Location: Goodna, Queensland

Post by Bartso »

i'd go to nissan these aftermarket seals don't seal as good as nissan ones
MUD BEERS & MAYHEM 4x4 & SOCIAL Group
[url=http://www.fourbys.com.au/]Fourby's tyre and mechanical[/url]
[url=http://www.4wdmonthly.com.au/forum/showthread.php?t=24441/]My build up for ttc[/url]
Top
Posts: 5457
Joined: Sun Oct 27, 2002 9:49 am
Location: Sydney

Post by Shorty40 »

Bartso wrote:i'd go to nissan these aftermarket seals don't seal as good as nissan ones
Now you tell me after I have done it :lol:
Top
Posts: 3054
Joined: Mon Nov 03, 2003 4:30 pm
Location: Melbourne

Post by hottiemonster »

mines needed to be done too, diff full of mud, run genuine parts as they fit correctly and have no hastles.

recently just put a aftermarket exhaust manifold gasket on when doing to motor swap and its blown apart, it was only 2-3 months old!

genuine all the way!
Gq ute new built
Top
Posts: 42
Joined: Wed Apr 20, 2005 9:21 pm

Post by nalucas »

Don't forget there is two seals on the rear axles!! An inner and outer seal. The inner one is a piece of piss to replace, but the outer one will require you to remove the bearing. Removing the bearings will usually require a pretty heavy duty press, in the order of 30 tonne.

What can happen on the outer seal is that the seal lip can wear a groove on the shaft, which can lead to a leak. A new seal won't necessarily help. You can try installing the seal in a slightly different position or install a speedi sleeve over the shaft, which gives you a new surface.

Nathan
Top
Posts: 2820
Joined: Sun May 25, 2003 10:04 am
Location: Redbank Plains, QLD

Post by Daisy »

nalucas wrote:Don't forget there is two seals on the rear axles!! An inner and outer seal. The inner one is a piece of piss to replace, but the outer one will require you to remove the bearing. Removing the bearings will usually require a pretty heavy duty press, in the order of 30 tonne.

What can happen on the outer seal is that the seal lip can wear a groove on the shaft, which can lead to a leak. A new seal won't necessarily help. You can try installing the seal in a slightly different position or install a speedi sleeve over the shaft, which gives you a new surface.

Nathan
thats what i was referring to in regards to replacing the axle.. as it seems like an easier option.

TOM
custom bar work, 4x4 parts, trailers, anything out of steel/alloy :D
Top
Posts: 342
Joined: Mon Aug 01, 2005 4:18 pm
Location: Brisbane

Post by bluemq »

oh man I did mine with an aftermarket seal and it only lasted 1 weekend.

after changing to a nissan seal it has lasted 4 years
Top
Posts: 3054
Joined: Mon Nov 03, 2003 4:30 pm
Location: Melbourne

Post by hottiemonster »

bluemq wrote:oh man I did mine with an aftermarket seal and it only lasted 1 weekend.

after changing to a nissan seal it has lasted 4 years
exactly!
Gq ute new built
Top
Post Reply

Return to “Nissan”

Who is online

Users browsing this forum: No registered users and 8 guests