Notice: We request that you don't just set up a new account at this time if you are a previous user.
If you used to be one of our moderators, please feel free to reach out to Chris via the facebook Outerlimits4x4 group and he will get you set back up with access should he need you.
Recovery:If you cannot access your old email address and don't remember your password, please click here to log a change of email address so you can do a password reset.

V8 Conversion - 253/308, LS1/LS2 Questions???

Tech Talk for Nissan owners.

Moderators: toaddog, V8Patrol

Post Reply
Posts: 19
Joined: Sat Jun 21, 2008 12:38 pm
Location: Browns Plains, Sth Brisbane

V8 Conversion - 253/308, LS1/LS2 Questions???

Post by Dutchy74 »

Hi All,

i am tossing up the idea of exchanging my TB42 over to a V8, i have read some of the threads on here. my main question is: with the on board computer and wiring - where does this mount? and is it exposed to any water/mud.

i do enjoy deep water and mud - just concerned with these components getting wet/mud and the motor conking out - does any one have this issue with the LS1/LS2?



Alternately i was looking at a 253/308 or similar - something that does not have the wiring loom/CPU.



- Open to you varse array of experiences and rrecommendations of what style of V8 would suit my GQ.





Cheers



Dan
Posts: 2877
Joined: Mon May 10, 2004 9:46 pm
Location: Goodna QLD

Post by ludacris »

The LS motors run fine under water and you can mount the computer where ever you like. I would be going the biggest and badest fuel injected motor for sure.

Cris
Cris's 4 X 4 Accessories & Suspension 0404 736 325 Rock Sliders From $499
Posts: 90
Joined: Fri Sep 11, 2009 8:16 pm
Location: Ipswich

Post by BumbleBee »

I mounted my ECU inside the dash above the glovebox. I can easily access it for tuning and its out of harms way.
Posts: 19
Joined: Sat Jun 21, 2008 12:38 pm
Location: Browns Plains, Sth Brisbane

Post by Dutchy74 »

It has been siggested to Turbo the TB42... what size would you go - and where is brisbane would you go ??
Posts: 1208
Joined: Fri Nov 08, 2002 8:21 pm
Location: sunshine coast

Post by killalux »

LS1 no probs with the water, when i make a harness for them all relays and fuses go with the ecu, generally up under the dash somewhere.

That being said the LS1 ECU's are sealed and water resistant

Steve
KILLA KUSTOM KABLES
CUSTOM AUTO ELECTRICAL SPECIALISTS
0404811498
LS1 & DURAMAX ENGINE CONVERSIONS, DRIVE IN DRIVE OUT. PATROLS AND CRUISERS

LS1 STANDALONE HARNESS $475ex
Posts: 121
Joined: Wed Dec 24, 2008 6:39 am
Location: pomona, sunny coast

Post by grinch2 »

Dutchy74 wrote:It has been siggested to Turbo the TB42... what size would you go - and where is brisbane would you go ??
dont waist your time and effort, just go the ls1 you'll be a lot happier, i spent heaps of money with turbo's, efi, aftermarket ecu's, intercollers, clutches, gearboxes and heaps more on my rb30, never mad good useable power, then the motor blew and i pissed it all off and dropped in a ls1 and auto :D it was the best thing i ever did, i recon i would have spent as much as the ls1 swap on the turbo set up which made an un reliable car, i never had a drama with the ls1, which is now going to get dumpped in my gu. plus the v8 sounds heaps tuffer :armsup:
Posts: 1363
Joined: Tue May 13, 2003 10:54 am
Location: Scarborough, Qld

Post by bigbluemav »

ludacris wrote:The LS motors run fine under water and you can mount the computer where ever you like. Cris
I didn't know THAT!! That's a definite PLUS!! Combined with putting the ECU in the cab, that's a REALLY GOOD couple of things!!

If you do, go the L76/L98 6 litre. WAY MORE low and mid range than a stock LS1.
Big Dave, Scarborough, Qld
Loose Screws 4wd Racing Team
Posts: 19
Joined: Sat Jun 21, 2008 12:38 pm
Location: Browns Plains, Sth Brisbane

Post by Dutchy74 »

bigbluemav wrote:
ludacris wrote:The LS motors run fine under water and you can mount the computer where ever you like. Cris
I didn't know THAT!! That's a definite PLUS!! Combined with putting the ECU in the cab, that's a REALLY GOOD couple of things!!

If you do, go the L76/L98 6 litre. WAY MORE low and mid range than a stock LS1.
What sort of $$$$ is ie for a L76/L98 6 litre...anyone around Brissy do this conversion...???
Posts: 1208
Joined: Fri Nov 08, 2002 8:21 pm
Location: sunshine coast

Post by killalux »

Hey, I just bought a low k VE LS2 6.0L for $6000. I can do the conversions if you are interested. i am on the sunshine coast.

Steve
KILLA KUSTOM KABLES
CUSTOM AUTO ELECTRICAL SPECIALISTS
0404811498
LS1 & DURAMAX ENGINE CONVERSIONS, DRIVE IN DRIVE OUT. PATROLS AND CRUISERS

LS1 STANDALONE HARNESS $475ex
Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests