Outer Limits 4x4 Board

Hi Loosecanon. I think it could be called a crossmember. Anyhow managed to buy one from 4wd wreckers in Marigold st, Revesby. Cost $140, what a rip off. Will fit next weekend.

Been searching for a while for this rear mount. Seems that HJ47 parts are starting to get hard to come by. I was wondering if perhaps I can use this bracket from a 60 series. I think the 60 series chassis rail is wider so I don't mind modifying as long as its cutting shorter and re-drilling the ...

I have a rebuilt 2H engine and a split transfer case that I would like to put into my FJ40. My question is that the rear engine supports on the FJ40 are on the bell housing. Whereas the 2H rear engine support is on the underside of the gearbox. Does anyone know if the 3 piece brackets from any other ...

Done this mod a while ago but now need to fit the speedo cable. Cable to short due to extra length of gearbox. Does anyone know if the speedo cable off a 5 speed late model bj43 will fit. I think these were released in 83.

Thanks AZZA FJ40, I will remove the pins to improve downwards flex. Do you know which leafs are used in the upwards flex? Would like just a bit more upwards flex say 50-75mm.

Do you thing it would be worth removing the two small leafs, which are I believe the load leafs?

so do you think I should use 2 long leafs from fj55 and all fj40 leafs except 2 long leafs and bottom load spring.

I am about to install fj55 rear leafs on the rear of my fj40. Since a fj55 is heavier than the fj40 I would like to remove a few of the leafs to achieve better offroad ability, more flex. But I still would like to use as daily drive so not to soft. Does anyone have experince with selection of leafs ...

Does anyone have experince with selection of leafs as I dont know which leaves to use. I have one set of fj40 and one set of fj55 rear leafs. Maybe a combination of two will give me what I want, which is good offroad but still drivable on road as I use as a daily drive.

So I need to locate a 60 series damper mount from somewhere and a 60 series damper.
I think I'll just by a new damper. Does anyone recommend a standard or RTC damper.
What about the other end of the damper to the tie rod? What have everyone else used?

I have installed power steering on my fj40 and I need to fit a damper. Do I buy a damper for a 40 , 60 series or custom? Do I need a RTC damper? Do I need to buy brackets that clamp around tie bar to give me somewhere to connect damper. Any info would be appreciated. I have read the 40 series ...

Ok. I've managed to order a set of Bushes so I now need to get the springs ready.
So does anyone know what spring leafs should I remove to get good results with flex in mind. I currently have 9 leafs. I'd like to remove the bottom two at leased as they are straight and alot thicker than the rest.

Found this manual whilst searching on the internet for bushing dimensions. Its the Bush Type Size Register for Whiteline. I'll study this on weekend and try to pick the right one. What Bush does anyone else reckon is correct? http://www.whiteline.com.au/Plus/pdf/WHITELINE%20PLUS%20BUSH%20TYPE%20SIZE ...

Measured the spring eye with a vernier and it measures 30mm.

It would be pretty good if those datsun 200B wagon bushes work. I will definately try to get to a parts store and have a look as it would be a easy solution

I have purchased a rear set of FJ55 springs for my fj40 the only problem I have is that they have large eye as apposed to small eye on 77 model fj. Does anyone now if I can sleeve the leaf spring eyes from 30mm to 25mm as to take small bushes and original pins or do I have to purchase chassis mounts ...

I have just installed a Bestop soft top on my fj40 and was about to install the soft door when I realised that I will not have any side mirrors as they are mounted on the doors. Does anyone know where I can purchase some side mirrors that mount onto the windscreen hinges or If anyone has made ...

I have very noisy tappets on my pajero, anyone know if they can be adjusted or are they hydraulic and need to be replaced.

Docdeath can u tell me if u managed to fit your fj45 transfer case on your h55f gearbox. I am in the process of trying to do this conversion myself and have also had problems with the Linkage located in wrong place. I have also found that u have to use the 60 series transfer case housing as the ...

pm modified toy

Can turbo4t tell me how this worked out as I am looking to fit a 5 speed from a 60 series with vacuum into a fj45. Just need to know if there is enough clearence between the vacuum unit and the chassis rail.

Just get it powder coated. Works great with aluminium

I have a 2f. Been modified to run on gas. Campbelltown /sydney

Hi joe fj45 yer, 200 litre is a good size. Do u know where It came from. Its about the size I am looking for. How is it strapped to the tray. Any pixs would be good

Hi, Zeyphly can u tell me how it was attached to the tray? I was thinking that maybe I can attach my tank to the steel rails on the tray.

I have a fj45 with a 6 cylinder diesel and would like a greater mileage range between refuelling. Can anyone tell me if I should mount the second tank by strapping it to the bottom of the aluminium tray or should I secure it to the chassis rail. If anyone has information would be greatly appreciated.

I have a B short engine for sale. Bought second hand a few years ago from the rustiest 40 I've ever seen. Used for putting boats in and out of water down south coast. Engine looks rusty but very little wear on crank and bores.

Spoke to consulmotive and he reconds that if the new rta laws came in then all previous engineered cars will have to comply with new laws. Just going to finish soa conversion on my 4wd and worry about rta laws later. Have to do it sooner rather than later

I wonder if anyone could recommend a engineer in South West sydney area. What was consulmotive engineers like Ozy1.

I have a FJ40 that I have been Modifying over the last couple of years. I am about halfway through a SOA convertion. I was told by a fellow 4X4 driver that as from 1st June 2005 I will no longer be able to engineer this vehicle unless it has been engineered on anything else before this date, which ...

Has anyone tried to engineer the 4x4labs steering arms in NSW.