Outer Limits 4x4 Board

c.mon guys someone out there must stock height of the crusier or even a copy of the standard specs.

BUMP

hey any chancxe of you being able to send me a copy of that

thanks

hey boys, just wanting to know the standard eye brow hieght of the above vehicle. As just put on new spring kit in and it is supposed to be a 2" lift and ity appears to have gone bearly .5". This has no body lift could some please tell me the measurment so I can double check this before I ripp ...

Hey guys I am looking at buying a 62 series what something that is reliable but yet econimical to run for a 4wd. It is to be used 40% off road and 60% on road what would be better a HJ62 or a FJ62 on duel fuel/straight gas. Also what is the average fuel usage of both. Thanks Guys.

So guys I have a P40 81 SWb what would its ratio be as reading the posts one person said 4.1 and another said 4.3 which is it?

So guys I have a P40 81 SWb what would its ratio be as reading the posts one person said 4.1 and another said 4.3 which is it?

i wish i had the cash to fix it properly but i bought it for $1000 and spent close to anthoer $1000 just trying to make it roadworthy and it still needs another couple of hundred spent on it and the cash supply has run real short and the need for a second vehicle is desperate.

hey all,

I was wondering if any one knows of somewhere in the western part of Melb to get a roadie down at a good price and who is a bit more tolerant of old 4wd's.

Thanks Troll

Hey guys, I have a MQ with 32x11.5R15 on her all the rest is stock do you find that the gearing is to high. why i say this is that went out with a mate who has a 60 sereies cruiser and when he is in 3/4 gear crusing along the gravel roads I am in second. And low range in mine is nowwhere as low as ...

Hey all I recently posted about the clutch on my MQ not working at all well the gearbox is out and on the ground. :P Well it was the clucth plate that was screwd one of the four springs that are on the plate had snapped the retaing lip and come out and the smaller inner one is lodge in the drive ...

thanks for all the replys guys. you have all confirmed what i thought it is time for a new clutch :cry: . Do any of you guys know of somwhere in Melb that does a clutch kit for a reasonable price? Also the guy i bought it off has a very large breather hose going into the clutch housing because it ...

Hey all, I have a mq with 4.1 ford crossflow under the bonnet. It has been off the road for several months now due to problem with the clutch. what is happing is it starts fine out of gear, but put your foot on the clutch and try to select a gear and it will not go into any gear. Turn off and select ...

What he has done is the pass side wheel bearing has siezed on the highway and ripped the axle to shreds and is unable to get the rest of the axle out as it seems to have chewed up the insides of the diff with it. He wants to know if the mounting points for the springs are further aprt or closer or ...

Hey all,

Just asking a question for a mate. He has a 62 series 1988 model crusier he has killed the rear axle and diff. He wants to know if there is different width's in mounting points for different models. Ie can he use a 60 series diff or not?

Thanks

Hey,

I have a MQ on straight gas and your setup sounds the same as mine. Mine has three screws and three small bolts and yeah you just undo those lift the plate off and the filter comes out. Also check the model number of the filter as it won't be a patrol filter.

The Trol

Hey guys just new to this site not sure if this is the right section what I am chasing is some info on a philips UHF cb model FM92. What I am after is the instruction book. Also could any tell me where I would get a new mike for this unit has I just bought it off ebay. I beleive the mike is a 7 pin ...