Outer Limits 4x4 Board

Yup i do with no probs.

Wires are rated to over 15amps anyway.

so it will work with mechanical beadlock as well? As in outer ring.

Cheers

Use mild steel and just paint it.

aluminum is the best

you going to whack a blow off off valve on it?

yah i just got a second hand low k's motor of here. They come up every now and then.

Or pull the thing apart and whack new rings in. Its only nuts and bolts lol (term used loosely haha)

yer it pisses me off how everything with 4x4 attached at the end gets marked up to a stupid price

Make them yourself, Theres a thread on nissan section somewhere about them. Off memory you cant go wider that 14mm.

nah ive seen garretts that look like yours dont worry about it.
Pretty sure your wastegate and blow off valve are tial

You can get lpg at the lpg place just down the road from BP in kilcoy.

Get ready for dents and damage going to cruiser!!!

First time i went it was countless close calls to rolling hehe I was in an old MQ with 31's though.

Also take more than enough grog. Its a pain in the ass when you run out.

If you go offroad heaps just get 35's they are handy as.

Your patrol should already have a lsd in the back. Just need new ratio gears. Can get them off ebay fairly cheap.

If you dont go offroad much then get a set of 31's too cruise around on then get some 35 simexs or swampers or whatever for ...

Same deal as auto-lockers, Can get them way cheaper straight from the states. Although i got mine cheaper from aus but i was lucky $320.

Suppose our strong dollar helps.

Im running a pertronix with the matching 40 000v flame thrower coil with petrol. Not using the ballast resistor. It starts and ...

Im almost done with mine. Ill stick up some shots

Adjust your wastegate to what psi you want

This is the only qld place they recommend,

Tony Motson's Performance Centre Brisbane 07 3277 7766 Ben

It looks like your car is tuned in good anyway looking at your dyno sheet. Wait till you intercool it then pump up the boost.


I sent you a pm pgm cheers

zd30 air box, it bolts straight in! no drilling holes.It lines up to the snorkel aswell. I think they are the same as the gu td42t air box which looks like it will fit up also.

thats from den81

no comment hahaha

pertronix is the proven solution.

I put it in mine and raced my mates right next to me.

Identical cars and mine one by a car length.

There should be a thread a few pages back.

Where do you get those white gauges? They look sweet, Ive got to take my dash of because the lights behind gauges crapped themselves lol.

Sounds awesome, what blow off valve you got? Im going for a hks ssq or maybe a monsta copy of ebay. they only 79 bucks. See how i go getting a 2nd hand hks one.

many thanks. Which year model does this apply for?

Ill call wreckers tommorrow

what about height?


cheers

Im wondering what the diamensions of the front windscreen are on sierras.

Ive got to put a window in back of my patrol ute. Ill attach picture

Ive been reading a bit on holden forums and it seems for them to get decent figures from there VL turbo's they run 425cfm mixers with at least two b2 converters. Next step is to go twin lines and then you lose your fuel gauge sender. They run higher psi as well quite fine. good power from 15psi. 250 ...

Or a louder more annoying girlfriend

What is your exhuast system?

I was going to go a straight through 3 inch and see what its like then maybe get a muffler

So just in seeing crankycruisers thread will we need a high angle shafts with x links?

Ive got a short wheel base GQ.

Cheers

bumpstop extension

$22500 ouch!!!.

Better off getting a crate v8 or something else. You could even import some gear from dubai to do something different :D

Mulisha i think you should just whack on a snorkle and air box setup.

Im going to intercool mine as i might as well get it all setup from the start. good old ...

I just heated my crossmember up with an oxy then belted it in. easy.

I had 5 inch and my front shaft definatly hit.

You can go as high as you like just get width to compensate.

I had 38 boggers with 2 inch body and 5 inch springs and extensive guard chopping and they rubbed really bad. Most tyres ...

He meant at flywheel ;)



Specifications
Nissan TB42 engine

Intermittent output (SAE Gross J1349)


152 Hp @ 3,600 rpm

Continuous output (SAE Gross J1349)


137 Hp @ 3,600 rpm

Peak torque (SAE Gross J1349)


32.5 kg-m (235 ft-lb) @ 2,800 rpm

Minimum fuel consumption


210 g/Hp·hr (0.463 ...

mod front crossmember for clearance and flip rear shaft

We really need to put a tutorial in the bible.

yah he had it all done at chapmans. Ive only ever heard good things of them but zero personal experience