Outer Limits 4x4 Board

Went to replace the globes in my head lights and realalised that they are sealed beam is there a replacement light you can use or are we stuck with the nissian sealed beams

thanks

Looks like i have done the head or gasket in who is good and trusted in Canberra to get it done by

mines a 95 mod and there are bolt holes in the floor 3 for the middle seat and 2 for the dicky seat there are pre cut spot in the vinal flooring about 50 x 30 mm in size.

thanks guys makes me feel a bit better now i know its normal

I know this must have been asked 1000 times but is 28l /100ks on gas acceptable for a 4.2efi lwb gq
AND
is it possible to put the gas tank lengthways down the car were the petrol tank now sitts as i want to put in a long range petrol tank in for outback touring.

just fixed my fuel tank you will need to have a 4inch slot cut out of it .
just mark were the arm is on the tank and TAKE IT TO A FABRICATER to do cost me $150 the have special rinses to put in the tank prior to cutting and welding the tank.

the diff was recoed when the air locker went in but i hadn't driven it with the hubs locked on the road

just had the airlocker installed in the front and driving home on the black top in 2 wheel and hubs locked not diff and at 80 ks + it get a droning noise with a slight vibration. 31 at tyres 5" lift with correct castor angles
unlock the hubs no noise or vibrations
Is this normal

i know this have been covered 100 time but i am still as confused as hell
i currently have a stock standard 95 gq LWB with lpg under back it has the flarey gaurds but i dont want to cut the body

i was looking at a 4" spring and 2" body lift and running 34jt2 or 35 peds simex but will go to 33 if ...

This has got to be a stupid question but have just got a gq patrol and know very little about moding it.

i am wanting to put 35'simex on it but are the bolt patterns offset/backspace the same as the cruiser

and are there any problems with a 4'' suspension 2'' body lift mainly concerned about the ...

sorry it was 100mm backspace not offset 15 x 8
No loom on the wolf they dont make one you need to wire it in hence i got the new pins
hope this helps

getting rid of my surplus stuff on ebay if interested

93 Discovery
http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=4607614795&rd=1&sspagename=STRK%3AMESE%3AIT&rd=1

Landrover Discovery 3.9l computer
http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=4607624563&rd=1&sspagename=STRK%3AMESE ...

what type of realistic fuel figures do you expect out of the 4500 98 auto 100 serries i am looking at getting one

Looking at buying a lateish model dual cab hilux to replace the disco
It will be mostly touring and moderate offroad 4wding

What problems do i look for and what are the engines like, petrol vs desiel and is the ifs any good and to what height can you raise them.

has any one had vibration problem in there serria at low speed 0-20k and then when you take you foot off at 80+k put the foot back down instantly goes away or at least 95% of it

I have checked the transfer and it is fine gearbox has just been checked out and is a litte worn in the bearings but ...

honda prelude seat fit perfectly and are super suportive and comfy.No modifications needed

someone must know were i can get this fitted even if its in Sydney as i am desperate i have a stuffed air flow and getting 30l /100ks at the moment.

Does anyone know of any reputable mechanic that know what they are doing to fit a V3 wolf unit into my disc in Canberra/queanbeyan area.

the original rubber burns very easily if you have an oxy/ acteteylene 2/3 minutes will burn the rubber out without overheating the chassis.

i am currently running 5.12 diff ratios in my serria which i believe are vitara diffs but
can anyone tell me what year/ model vitara do you get these diff out of

what size offset did you end up getting as im trying to fit 34 to mine but ive got a spoa

just had mine replaced last week for $255 seal and screen in Canberra.
it didnt look that easy to do yourself though

how close are the bolt patterns as i am trying to fit rover rims on a suki and were looking at having them redrilled

i have recently put in a new 4l engine into my 93 3.5l disco the 4l is set up with all the 3.5 sensors these have been checked or replaced, including the air flow sensor and computer and all are within the required peremiters
The problem is that my fuel figures are around 28-30/100kms has anyone ...

running merc steering arms bolted to disc brakes cost $20 from wreckers

just finished doing this last week you will need to rheem out about .5mm to make the bolt holes line up i already had a zlink which was cut to the new length sleeved and welded. $75 each is a bit steep as i picked mine up in Canberra for $40 for the pair

what is involved in shaving a diff and who does it

Thanks guys i am getting it from roadlessgear in the states au price is $220 but a mate is bring it back as he goes there for business and is never near his laugage weight otherwise it was $40 frieght to canberra

wanting to know what is the better diff locker as air locker are out of the price range at the moment

Was looking at lock rite or detroit as i can get these new for $220 is one better then the other.